Beautiful Ancient Elements Textured Silver Earrings(jewelry tutorial)





Resources Necessary
Two '/*" x Γ 18-gauge sterling silver sheet silver Two 7/«" sterling silver bar components Two five.three mm x 3.2 mm sixteen-gauge sterling silver oval soar rings Two sterling silver ear wires
Instruments Essential
Ruler
Marker
Jeweler's noticed or tin snips Masking tape
Concrete block or landscape paver
Hammer
File
Fantastic grit sanding pad Awl
Difficult, flat surface /ΐί’ drill little bit
Handheld rotary Device, flex shaft, or drill press Liver of sulfur or oxidizing Alternative High-quality steel wool Polishing fabric
Two pairs of chain nose pliers


1.Utilize the ruler to measure and mark two
rectangle parts of 18-gauge sterling sheet silver.
two.Utilizing a jeweler's saw or tin snips, Slice the 18-gauge sterling sheet silver into two Vi" x Γ rectangles (if you will be building the bracelet and pendant tasks, you might want to Lower all of the rectangle silver items needed for another tasks and texture all of them at a single time).
three.Location The 2 W x Γ sterling silver rectangle parts onto the sticky aspect of the piece of masking tape. This will assist you to to carry the silver rectangles in place while you're texturing them, and will likely assist to maintain your fingertips at a secure length to avoid hitting them With all the hammer.
four.Position the bit of masking tape with the silver rectangles sticky side down onto a concrete block or landscape paver.

5.Using a hammer, gently strike the tape-protected silver rectangles employing a business strike, but You should not strike much too hard. You are able to attain the desired texture much more effortlessly with numerous gentle strikes instead of a few hard strikes. Carry the tape routinely and Test the progress from the texturing, ensuring that that all the surface area from the silver rectangles is acquiring a uniform texture. The surface area will appear comparable to sandpaper Should you be using a concrete block. After you obtain the desired texture, clear away the silver rectangles from your masking tape.
six.the silver rectangles can have a slight curve to them, and the sides will likely be misshapen and sharp When you texture them. You'll be able to go away the silver rectangles curved or, to flatten them, location the silver rectangles on a tough, flat area and use a rawhide mallet to flatten them. If you do not Have got a rawhide mallet, you are able to position the silver rectangles on a tough, flat surface, go over the parts with a thick piece of scrap leather, and make use of a hammer to Carefully faucet the leather-based covered silver rectangles to flatten them.

7.You need to make use of a file to remove any tough or sharp edges. Utilize a great grit sanding pad to go over the area where you have submitted to sleek the sides and take away any file marks.

eight.Evaluate from one particular conclusion of each and every textured silver rectangle and position a mark in the middle of every bit. This is where the holes will probably be drilled to attach the bounce ring and bar elements.
9.Put on the security Eyeglasses. Area the textured silver rectangles onto a hard, flat area. Position the point in the awl around the mark that you simply made '/t" from the conclusion on the rectangle pieces and utilize a men's rings hammer to firmly strike after on the top of your awl to generate a pilot hole for drilling the holes in the silver rectangles.
10.Employing a drill bit, drill holes into Just about every in the silver rectangles with a handheld rotary Resource, flex shaft, or drill push. Remember to have on security Eyeglasses.
eleven.Use the file or sanding pad to reduce any burs or rough edges still left from drilling holes into your silver rectangles.
12.Implement liver of sulfur or oxidizing Alternative for the textured silver rectangles, bar parts. and bounce rings. It is essential to observe any protection recommendations the producer indicates when dealing with any substances.

thirteen.Following making use of the oxidizing Resolution, use great metal wool to remove the darkened locations within the elevated surface area in the silver rectangles, leaving several of the textured parts dim. Rub the high-quality metal wool about men's rings the soar rings and bar parts to get rid of some but not all the darkened locations. Rinse with water, dry, and rub with sprucing fabric.

14.With two pair of chain nose pliers pointing up, keep the soar ring Together with the opening at the highest. Roll a single of one's wrists away from both you and your other wrist toward you, opening the bounce men's college ring ring only just as much as needed. To close the bounce ring, maintain it exactly the same way and roll your wrists in the alternative route (consider Keeping a piece of paper silver rings for men and tearing it). Hardly ever pull the leap ring finishes out as this will likely weaken the metal, and it will be tricky to near the bounce ring.
15.Insert the bar component and textured silver rectangle to your jump ring. Near the bounce ring.
16.Gently open up the loop at gents ring the bottom on the ear wire, increase another conclude of the bar element. and afterwards close the ear wire loop.
17.Repeat these methods for the 2nd earring.







Leave a Reply

Your email address will not be published. Required fields are marked *